R Safety Hub R Safety Hub Your prescription for a safer workplace

Cutting Fiber Cement Siding

Lines in italics are for the reader, not the crew. If you can, have the saw and its dust collector in front of the crew while you read. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is about the cloud. You know the one. Somebody rips a plank of fiber cement siding with a bare saw and the whole side of the house goes gray for a minute.

That cloud is not just dirt. Fiber cement has silica in it, and the fine dust you can't even see is the part that gets into your lungs and stays there. Silica dust can cause lung disease, cancer, and harm to the kidneys and immune system, and it does not wash out.

The setup the rule spells out

Washington's silica rule has a table of tasks, and cutting fiber cement board with a handheld saw is on it. If you follow that table, here's the setup.

A handheld power saw with a blade eight inches or smaller.

A dust collection system on the saw, the kind you can buy for it, hooked to a vacuum.

The vacuum has to pull at least the airflow the saw's maker calls for, and have a filter that catches ninety-nine percent or more.

Run and maintain the saw and the collector the way the maker says, so they keep the dust down.

And this one gets missed: outdoors only. That setup is only for cutting outside.

Done that way, the table does not call for a respirator.

Where it goes wrong

Cutting in the garage because it's raining. That's not outdoors, and that table line no longer covers you. The company has to use another way that keeps your exposure under the limit. Ask before you set up inside.

A full vacuum, a clogged filter or a loose hose. The setup only counts if it's working. If the dust is blowing out, stop and fix it.

Pulling the collector off because "it's just one cut." One cut is still a cloud.

Some crews cut with hand shears or score and snap. Those aren't in the rule's table, because they make very little dust. Federal OSHA says hand shears usually keep the dust below the level where the silica rule kicks in, and the siding maker says the same for score and snap. In Washington, the company backs that up in its written silica plan, so ask your supervisor what the plan says.

Cleanup

No dry sweeping and no blowing dust off with compressed air, if it puts silica in the air. Use a HEPA-filter vacuum, or wet it down and sweep. And don't blow off your clothes with the air hose.

Your part

The company has a written silica plan that says how each dusty job gets done, and you have the right to see it. A competent person checks the job to make sure the plan is followed. Find out who that is. Your part is to set the saw up right, keep it working, and speak up if it isn't.

One crew member always says, "I've been cutting this stuff for years and I'm fine." Silica takes years to show up. That's exactly the problem.

Talk it over

  1. When is the last time anybody checked our vacuum filter?
  2. What do we do on this job when it's raining and the cuts still need to happen?

Before you go

Saw with dust collection, vacuum and filter working, outdoors only, and no dry sweeping or blowing it around.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-840-110 intro, (1) (Table 1 controls fully and properly implemented, unless exposure is assessed and limited under WAC 296-840-105) and Table 1 row (iii) (hand-held power saws for cutting fiber-cement board, blade diameter 8 inches or less; for tasks performed outdoors only; saw with commercially available dust collection system; operate and maintain per manufacturer's instructions to minimize dust emissions; dust collector provides the air flow the tool manufacturer recommends or greater and a filter with 99% or greater efficiency; required respiratory protection: none, at four hours or less and over four hours); 296-840-135(1), (2) (no dry sweeping or dry brushing, and no compressed air on clothing or surfaces, where it could contribute to exposure, unless the rule's exceptions apply); 296-840-140(1), (3), (4)(b) (written exposure control plan; available to each covered employee on request; competent person makes frequent and regular inspections); 296-840-105 (exposure assessment when Table 1 is not followed); 296-840-150 (hazards named in training). Federal: 29 CFR 1926.1153(c)(1) and Table 1 row (iii) (same controls), (f) (housekeeping), (g) (written exposure control plan). "Lung disease and cancer" follows the hazards the rule names for training; "does not wash out," "one cut is still a cloud," "silica takes years to show up," the garage example, "wet it down and sweep" (our plain wording of wet sweeping), "hooked to a vacuum" (the rule says dust collector), the shears and score-and-snap line, and the full-vacuum and loose-hose examples are plain explanation or good practice, not rule text. The rule's Table 1 does not list shears or score-and-snap; the talk makes no claim about how much dust they make.