R Safety Hub R Safety Hub Your prescription for a safer workplace

Flammable Liquids in the Shop

Lines in italics are for the reader, not the crew. If you can, read this one standing next to the shop's flammable storage cabinet. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is flammable liquids in the shop: solvents, thinners, fuel, and some paints, glues and cleaners.

Picture a can of thinner on a bench with the lid off. Across the shop, somebody starts grinding.

The liquid isn't what catches fire. It's the vapor coming off it, and you can't see it. It can drift low across the floor, and if it finds a spark, the fire can run right back to the can.

So the job is two things: keep the vapor in, and keep the sparks away.

Keep the lid on

For the more flammable liquids, Washington's rule says the container stays covered whenever it's not actually being used. We keep the lid on all of them. That's just good practice.

When you're done, the can goes back in the cabinet. Never leave one in a doorway, an aisle or by the stairs. That's the way out.

Keep sparks away

The rule says the more flammable liquids are used only where there's no open flame or other ignition source anywhere the vapor could travel. That means smoking, welding, cutting, sparks, hot surfaces, even static.

So before you open a can, look around. And welding, cutting or tools that throw sparks only happen with the person in charge supervising, after they've looked the area over. That's in the rule too.

Pouring it

When you fill a can with one of the more flammable liquids, the rule says the spout and the can are connected, metal to metal, usually with a bond wire. Static can spark, and one tiny spark at the opening is all the vapor needs.

Not sure how to hook it up? Ask your supervisor before you pour.

Rags and spills

Wipe up spills right away. Used rags go in the covered metal can, not a pile on the bench. That can gets emptied every day, because rags soaked with some oils and finishes can heat up and catch fire on their own.

If the rag can is full or a lid is missing, tell your supervisor, so it gets fixed.

Somebody always says, "It's just a little thinner." A little thinner makes a lot of vapor.

Talk it over

  1. You just finished wiping down a part with solvent. What happens to the can, and what happens to the rag?
  2. What would make it easier or safer for us to work with flammable liquids in this shop, even on a busy day?

Before you go

Lid on, sparks away, bond when you pour, and rags in the metal can.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-24-33011(2)(d)(i) (Category 1 or 2 flammable liquids, or Category 3 with a flashpoint below 100°F, kept in covered containers when not actually in use; the talk says "the more flammable liquids"), (2)(d)(iii) (those liquids used only where there are no open flames or other sources of ignition within the possible path of vapor travel), (6)(a) (adequate precautions against ignition of vapors; the rule's list of sources includes open flames, smoking, cutting and welding, hot surfaces, frictional heat, static, electrical and mechanical sparks and spontaneous ignition), (6)(b) (those liquids not dispensed into containers unless the nozzle and container are electrically interconnected; a bond wire, or a metal floorplate connected to the fill stem, meets it), (8) (hot work such as welding or cutting, spark-producing power tools and chipping only under supervision of an individual in responsible charge, who inspects the area first; the paragraph is headed "Repairs to equipment"), (9)(a) (spills cleaned up promptly), (9)(c) (combustible waste material and residues kept to a minimum, in covered metal receptacles, disposed of daily). WAC 296-24-33009(5)(a) (flammable liquids not stored so as to limit use of exits, stairways or areas normally used for safe egress; the talk gives this without saying "the rule says"). Federal: 29 CFR 1910.106(e)(2)(iv), (e)(6), (e)(8), (e)(9) and (d)(5)(i) say the same things in the same words; no difference found on any line this talk uses.