R Safety Hub R Safety Hub Your prescription for a safer workplace

Grinders and Abrasive Wheels

Lines in italics are for the reader, not the crew. If you can, hold up one of the crew's angle grinders, unplugged, with the guard on. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is the angle grinder. And the bench grinder, if we have one. The tool that cuts, grinds, cleans up welds, takes the burr off, and does a hundred other jobs.

Here is the thing to remember about a grinding wheel. It spins fast enough that if it comes apart, the pieces don't fall. They fly. That is why almost every rule about grinders is about two things: the wheel, and the guard.

The guard stays on

Washington's rule says grinders have guards. And a power tool built to take a guard has the guard on when it's being used.

The guard isn't there to look nice. It has to be strong enough to hold the pieces of a wheel that breaks. It is the thing standing between those pieces and you.

So the guard doesn't come off because it gets in the way. It doesn't get turned around to face the wrong side. If a job seems to need the guard off, the job needs a different tool or a different wheel. Talk to your supervisor.

Somebody always says, "I've run it without the guard for years." Fair enough. I've also driven for years without hitting a deer. I still don't take the headlights off.

Look at the wheel before it goes on

Every wheel gets looked over closely before it's mounted, to make sure it's free of cracks and defects. Chips, cracks, a dropped wheel, a wheel that got wet or crushed in the bottom of the bucket. If you have a doubt, it doesn't go on.

The rule also says the wheel gets ring-tested before mounting. Ask your supervisor or follow the maker's directions for how. If you're not sure how, that's a good thing to learn this week.

When it goes on: it should slide onto the spindle freely. Never force it. And the nut gets tightened enough to hold it. Not cranked down with all you've got.

Match the wheel to the tool

This part is good practice and the maker's label, not the rule's own words. Every wheel is marked with how fast it's allowed to spin. The tool is marked with how fast it spins. The wheel has to be rated for at least as fast as the tool. A small wheel off one tool put on a faster tool is a wheel waiting to fly apart.

And use the wheel made for the job. A cutting wheel is thin and made for cutting, not side grinding. Read the label.

Eyes and face

Everyone using a grinding wheel wears eye protection. Safety glasses at least. For a lot of grinding, add a face shield over the glasses. That's good practice, and for one small kind of wheel the rule requires both.

Think about the person next to you, too. Sparks and chips don't care whose job it is. Point the spray away from people.

A couple more habits

These are good practice, not the rule. When you start a fresh wheel, stand off to the side for a moment and let it come up to speed, away from anybody. Keep two hands on the tool. Let it stop before you set it down. Unplug it, or pull the battery, before you change a wheel.

And a bench grinder's tool rest stays tight to the wheel. The rule says no more than an eighth of an inch. Any bigger, and a piece can get pulled in.

Talk it over

  1. Look at the grinders on this job right now. Is every guard on and facing the right way?
  2. And where do our spare wheels live, and are any of them chipped, wet or crushed?

Before you go

Guard on. Look at the wheel before it goes on. Wheel rated for the tool. Eyes covered, face too when you grind.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-155-365(2) (grinders have guards), (3)(e) (required guards strong enough to retain wheel fragments), (3)(g) (inspect and ring-test before mounting), (3)(h) (fit freely, not forced, nut only tight enough), (3)(i) (eye protection), (3)(c)(vi) (glasses and face shield for that small reinforced wheel), (3)(b) (work rest within 1/8 inch); 296-155-360(2)(a) (guards on when in use). Federal: 29 CFR 1926.303(b)(1), (c). The guard rule points to ANSI B7.1; this talk does not quote or describe it. Wheel speed matching, wheel type, a face shield for most grinding, standing aside at start-up, two hands, unplugging to change wheels and pointing sparks away are good practice and the maker's label, not rule text. No maker's document was read.