R Safety Hub R Safety Hub Your prescription for a safer workplace

Hand and Power Tool Safety (Construction)

CONSTRUCTION jobs (follows chapter 296-155 WAC)

Lines in italics are for the reader, not the crew. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is about the tools we use every day. Saws, nailers, drills, hammers, the whole bucket.

First, a real line from the Washington rule book. I'm not making this up. It says, "You must not cut nails with an axe." Somebody, somewhere, made that rule necessary. Let's not be the reason they write the next one.

Your tool or theirs, same rule

Every hand and power tool on this job has to be kept in safe condition. That counts whether the company bought it or you brought it from home. Your personal saw gets held to the same standard as the company saw.

Guards stay on

If a tool was built to take a guard, the guard stays on while you use it. On a circular saw, the lower guard has to snap back over the blade on its own the moment the saw leaves the cut. If yours hangs up, sticks, or somebody wedged it open, that saw is done for today. Tag it and get another one.

And the trigger on a circular saw is supposed to shut it off when you let go. If somebody rigged it to stay on, that's not a feature. That's a problem.

Air tools

Nailers and staplers that feed automatically need a nose safety, so they only fire when the nose is pressed against the work. Don't tape it, wire it, or pull it off. Washington allows one narrow exception for fine-wire brads and staples, and then everybody within twelve feet needs eye protection.

Hose connections have to be secured so they can't pop apart and whip around.

No blowing yourself off or cleaning the bench with full shop air. Cleaning with compressed air is allowed only below thirty pounds of pressure, with a chip guard and the right protection.

Cords and hoses are not rope

Never raise or lower a tool by its cord or its hose. That's in the rule for both. Use a hand line or a bucket. A cord was built to carry power, not a nail gun up two floors.

Electric tools have to be double-insulated or grounded. A plug with the ground pin broken off is not grounded, so that tool doesn't get used.

Hand tools

Hand tools get looked at too. A wrench with worn jaws that slip goes away. A chisel or wedge with a mushroomed head gets dressed or replaced. Mushroomed heads are not allowed. Wooden handles have to be tight, with no cracks or splinters.

Protect yourself

If the tool throws chips, dust or sparks, you wear the protection for it. Glasses at a minimum, and more when the job calls for it.

Good practice

Unplug it, or pull the battery, or disconnect the air, before you change a blade or a bit. Carry tools by the handle, not the cord. Never point a nailer at anybody, even as a joke. Especially as a joke. And look at the tool before you use it, not after. Those are good habits, not word-for-word rules.

Talk it over

  1. Is there a tool on this job right now with a guard that sticks, or a cord that's been taped?
  2. When was the last time you saw somebody lower a tool by its cord or hose?

Before you go

Guards on, cords off the rope job, and check it before you use it.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-155-350(1)–(4) (condition of tools whoever supplied them, guards, PPE, switches); 296-155-355 (hand tools, including "You must not cut nails with an axe"); 296-155-360(1)–(3) (cords, air tools, nailer muzzle safety and fine-wire exception, 30 psi cleaning, hoses, fuel tools); 296-155-370(1)–(2) (circular saw guards). Federal: 29 CFR 1926.300, 1926.301, 1926.302, 1926.304(d). Federal requires the nailer muzzle safety only above 100 psi at the tool; Washington has no psi threshold. Unplugging before blade changes and carrying by the handle are good practice.