R Safety Hub R Safety Hub Your prescription for a safer workplace

Jacks and Cribbing

Lines in italics are for the reader, not the crew. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is about jacks: bottle jacks, screw jacks, ratchet jacks. The ones we use to lift a beam, level a floor or raise a corner of a house. A jack is a lifting tool. It is not a holding tool. Hang on to that one idea and you have most of this talk.

Read the jack before you use it

Every jack has the maker's rated capacity marked on it, where you can read it. Don't go over it. If the marking is worn off, you don't know what it holds. Set it aside. That last part is good sense, not the rule's words.

Every jack has a positive stop, so it can't be run out past its travel. Don't try to get a little more out of it than it was built to give. The controls are built so the operator isn't put in danger.

Set it on something solid

If the ground or floor under the jack isn't a firm foundation, the rule says block or crib the base. Soft dirt, mud and rotten subfloor are our examples of not firm. A jack that sinks or tips drops the load.

If the metal cap on top could slip on the load, put a wood block between the cap and the load. Steel on steel likes to slide.

Crib it right away

After the load is raised, it gets cribbed, blocked or otherwise secured. Right away. Not after break. Not after you find the shims.

A jack holds pressure with seals and valves, and seals and valves can let go. Cribbing doesn't. So you raise it, you crib it, and then you work.

And here's our own rule on top of that one: no part of your body goes under a load held up only by a jack. Hands, arms, head, none of it. Somebody always says, "I'm only under there for a second." The jack doesn't know that.

Cold weather

Hydraulic jacks out in freezing weather need the right antifreeze fluid in them. A frozen jack can fail just when you need it.

Inspection and tagging

The rule wants jacks looked over thoroughly. At the least: every six months for a jack in steady or on-and-off use at one place, when a jack is sent out of the shop for special work and again when it comes back, and right before and after a jack takes an abnormal load or a shock. Jacks also get lubricated at regular intervals. Most of that is the company's job.

Your part is to notice. The rule doesn't list what makes a jack out of order, but a jack that leaks, creeps down or won't hold is, in our book. It gets tagged, and nobody uses it until it is repaired. If you dropped one, say so. And repair or replacement parts get checked for defects too. No mystery parts from the bottom of the toolbox.

Talk it over

  1. What do we have for cribbing, and is it close to where we jack?
  2. Has anybody seen a jack slowly creep down? What did we do with it?

Before you go

Read the capacity. Solid base. Raise it, crib it, then work. Never under a load on a jack alone.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-155-375(1) (maker's rated capacity legibly marked; not exceeded), (2) (positive stop to prevent over-travel), (3) (specially designed jacks need department approval; not in the talk), (4) (control parts designed so the operator is not exposed), (5) (block or crib the base when a firm foundation is needed; wood block between cap and load where the cap could slip), (6)(a) (after raising, immediately crib, block or otherwise secure), (6)(b) (antifreeze for hydraulic jacks exposed to freezing), (6)(c) (lubricated at regular intervals), (7) (thorough inspection at least every six months at one locality; when sent out and returned; immediately before and after an abnormal load or shock), (8) (repair or replacement parts examined for defects), (9) (out-of-order jacks tagged, not used until repaired). Federal: 29 CFR 1926.305(a), (c), (d). Differences seen: none in substance; Washington adds department approval for specially designed jacks and the operator-controls line. "A jack lifts, it doesn't hold," "never under a load held only by a jack," "seals and valves can let go," "raise a little, crib a little," "set aside a jack you can't read," and "no mystery parts" are good practice or plain sense, not rule text; the crib-as-you-go line is labelled aloud.