R Safety Hub R Safety Hub Your prescription for a safer workplace

Job-Made Wooden Ladders — Setting Up and Using (Part 2 of 2)

Lines in italics are for the reader, not the crew. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Last time was building and checking the homemade wooden ladder. Today is setting it up and using it. A good ladder set up wrong is still a bad day.

The angle

Measure the ladder's working length along the rails, from the foot to where it rests at the top. The foot sits out from the top support, measured flat across the ground, about one quarter of that length.

If the side rails are spliced, it goes steeper. The foot sits out no more than one eighth of the working length.

The top

Both side rails rest equally on the top support. And that top support has to be fairly rigid and strong enough to hold the load.

If it's your way up to another level, the rails go at least three feet above the landing. If it can't reach that high, three things. It gets secured at the top to something rigid that won't flex. There's a grab rail or something like it to hold getting on and off. And it can't bend enough under a load to slip off its support.

If it takes two ladders to get up there, they don't just stack end to end. They're offset, with a platform or landing between them.

The bottom

Firm, level footing, or the ladder gets secured. Never on boxes, barrels or anything else wobbly to gain height.

On ice, snow or anything slippery, it's secured, or it has slip-resistant feet. Even with good feet, place it with care.

If people, equipment or traffic could knock it, it's tied off or barricaded. If a door opens toward it, block the door open, lock it, or guard it.

Keep the area clear at the top and the bottom.

If it could touch exposed live wires or electrical equipment, it needs nonconductive side rails. A wood ladder with metal strips on the rails counts as conductive.

Climbing and working

Don't overload it. No more weight than it was built for. And use it only as a ladder, not as a plank, a brace or a ramp.

Face the ladder. At least one hand on it going up and coming down. Don't carry anything that could throw off your balance. Keep the cleats free of mud, oil and grease.

When you work from it, secure it top and bottom. And nobody moves, shifts or adjusts it while someone is on it.

The rule lists more; these are the common ones.

Scaffolds

A job-made ladder never holds up a ladder jack scaffold, or a step, platform or trestle ladder scaffold. Those need a ladder rated Type one or Type one A, or higher, set so it can't slip.

Talk it over

  1. Where on this job are we using a homemade ladder to reach another level? Does it stick up three feet?
  2. Is there anything piled at the bottom of one right now?

Before you go

Right angle, solid top, three feet above, firm footing, face it, one hand, tied off when you work, and never under a ladder jack.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-876-099 ("working length": measured along the rails from the base support point to the point of bearing at the top); 296-876-40020(1), (2), (3) (horizontal distance from top support to foot about one-quarter of working length; spliced side rails not greater than one-eighth; both rails supported at top); 296-876-40015(1), (2), (3), (5) (firm level footing or secured; on ice, snow or slippery surfaces secured or slip-resistant feet; not on boxes, barrels or other unstable bases; top support reasonably rigid and able to support the load); 296-876-40010(1), (2) (secured or barricaded where traffic or activities could displace it; doors opening toward it blocked, locked or guarded); 296-876-40030(1), (2), (3) (three-foot extension; if too short, secured at top to a rigid support that will not deflect, grasping device, deflection will not by itself cause slipping; two or more ladders offset with a platform or landing); 296-876-40025(1), (2), (3), (4), (6) (at least one hand; face the ladder; free of oil, grease or other slippery materials; area at top and bottom clear; no load that could cause loss of balance); 296-876-40040(1), (2) (not moved, shifted or adjusted while occupied; secured top and bottom when working from it); 296-874-40026(4), (5) and -40038(1), (2) (Type I or IA ladders under ladder jack and step, platform and trestle ladder scaffolds; job-made ladders not used to support them; both sections amended effective 8/21/26). Federal: 29 CFR 1926.1053(b) intro (use rules apply to job-made ladders), (b)(1), (b)(5)(i), (ii), (b)(6), (b)(7), (b)(8), (b)(9). 296-876-40005(1), (2) and note (intended purpose only; not as a brace, gangway, platform or scaffold plank unless the maker recommends it; not overloaded beyond maximum intended load or rated capacity); 296-876-40035 and note (nonconductive side rails where the ladder could contact uninsulated energized lines or equipment; wood with metal side rail reinforcement is conductive); 296-876-40015(4) (rails equally supported). Federal also (b)(2), (b)(3), (b)(10), (b)(12). "Mud" with oil and grease, "a good ladder set up wrong is still a bad day," and "they don't just stack end to end" are plain explanation. The work-from-a-ladder lines on safety belts over twenty-five feet (40040(3), (4)) are left out on purpose to keep the talk short; the talk says the list is shortened.