R Safety Hub R Safety Hub Your prescription for a safer workplace

Loading Trucks and Trailers With a Forklift — Dock Plates and Wheel Chocks

Lines in italics are for the reader, not the crew. If you can, read this one near the dock, well back from the edge. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is about the dock. Driving a forklift, or a powered pallet jack, across the gap and into the back of a truck or trailer.

Here's the thing about a trailer. It looks parked, but it's on wheels. A driver can pull out early. A trailer that isn't held can roll. If that gap opens while you're crossing it, there's nothing under you.

Hold it still

So here's the big one. The rule says that while a truck or trailer is being loaded or unloaded, its brakes are set and its wheels are chocked or blocked.

Some docks have a lock that grabs the trailer and holds it to the dock. That's allowed in place of chocks, as long as the lock is working and holding. If it's broken or won't catch, it's back to chocks, and tell your supervisor.

Good practice: see the chocks or the lock with your own eyes before your first trip in.

Somebody always says, "That driver's not going anywhere, they're at lunch." Great. Chock it anyway. Lunch ends.

Look at the floor

The rule also says to check the truck or trailer floor for breaks or weak spots before you drive on it. A forklift is heavy, and a worn-out trailer floor can let a wheel drop through. If the floor looks broken or rotten, stay out and tell your supervisor.

The dock plate

The plate is your bridge, so three things. It has to be rated for the weight going across it. It gets secured before anybody drives on it, so it can't slide out from under you. And you cross it slow and careful.

A trailer with no truck

One more. A trailer dropped at the dock with no truck hooked to it can tip on end when a forklift drives in. It may need jacks under the front first. If you're not sure, ask your supervisor before you go in.

Talk it over

  1. A truck backs in and the driver says, "I'm only here ten minutes." What has to happen before the first forklift goes in?
  2. What would make loading and unloading trucks easier or safer for us, even on a day when trucks are lined up and everybody's in a hurry?

Before you go

Brakes set. Wheels chocked or locked. Floor checked. Plate secured. Slow across.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-863-40050(1) (check the truck or trailer flooring for breaks or weakness before driving on it), (2)(a), (b) (prevent movement of trucks or trailers during loading or unloading by setting the brakes and chocking or blocking the wheels), exemptions 1 and 2 (mechanical means may be used instead of chocks or blocks to secure the trailer to the dock; chocks not required when the mechanical means prevents the trailer from moving away from the dock, is used and maintained as the manufacturer recommends, and damaged mechanical equipment is immediately removed from service; the talk says "working and holding" and "if it's broken or won't catch, it's back to chocks"), note (fixed jacks may be needed to keep a semi-trailer that is not coupled to a tractor from up ending during loading or unloading; the talk says "may need", as the rule does); WAC 296-863-40040(1)(b) (loads do not exceed the dock-board's rated capacity), (2)(a), (b) (drive slowly and carefully over dock-boards; properly secure them before driving on them); WAC 296-24-75006(3), (5) (portable dockboards secured against moving out of a safe position; wheel chocks, sand shoes or other positive measures keep the transport vehicle from moving while employees are on the dockboard); WAC 296-863-100 (the chapter covers forklifts and motorized hand trucks; a hand pallet jack with no motor is not covered, which is why the talk says "powered"). Federal: 29 CFR 1910.178(k)(1) (brakes of highway trucks set and wheel chocks under the rear wheels while boarded with powered industrial trucks), (k)(3) (fixed jacks may be necessary for a semitrailer not coupled to a tractor), (m)(7) (brakes set and wheel blocks in place while loading or unloading; flooring checked for breaks and weakness), (n)(11) (dockboards properly secured, driven over carefully and slowly, rated capacity never exceeded); 29 CFR 1910.26(c), (d). The federal rule says chocks under the rear wheels; the talk follows Washington's wording, chock or block the wheels.