← All talks
Printable version with sign-in sheet (PDF)
Read this out loud
Morning, everybody. Today is about machine guards. The table saw, the drill press, the grinder, the belt and pulley on the compressor.
A guard is like a seat belt. Most days it does nothing. It's there for one bad second. Everybody has one: somebody calls your name, a board kicks, you sneeze. The machine doesn't slow down for it.
Guards stay on
Putting the right guard on each machine is the company's part. Ours is leaving it there. Washington's rule says workers don't remove, move or damage a safeguard, and don't get in the way of anybody else using one. The way we read it, that covers wiring a guard back or propping it open, too.
If a guard really is in the way, don't fight it alone. Take it to your supervisor and work it out together. There may be a better guard or a better setup for that job.
Stopped means stopped
The rule says a power machine is completely stopped before anybody adjusts it, repairs it, or clears out material or scrap. The one exception is an adjustment that can only be made while it runs.
Completely stopped, not just switched off. A blade can keep coasting after the click. Wait for it.
And if the machine could start up while your hands are in it, that's a lockout job. Ask your supervisor how lockout works on that machine before you start.
Dress for it
The rule says no torn or loose clothing around machinery. Anything loose is a handle for the machine to grab. Tying back long hair and taking off rings is good practice, for the same reason.
When a guard isn't right
If you walk up to a machine and its guard is missing, loose, bent or cracked, don't run it. Tell your supervisor, so it gets fixed before it hurts somebody.
Somebody always says, "I'll just take it off for this one cut." Trouble is, the machine can't count.
Talk it over
- A piece of scrap is stuck next to the blade. What has to happen before anybody reaches for it?
- From where you stand at the machines, what would make it easier to keep every guard on and still get the work done?
Before you go
Guards stay on, machine stopped before you reach in, nothing loose on you, and a guard that isn't right goes to your supervisor.
Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.
Get started
Reference (not read aloud). Rule text behind the spoken "the rule says" lines: WAC 296-800-12005(7), (8) (employees must not remove, displace, damage, destroy or carry off any safeguard, notice or warning provided to make the workplace safe; must not interfere with use of any safeguard by anyone in the workplace), (5) (employees must not wear torn or loose clothing while working around machinery; the note under it says clothing, hair and jewelry can get caught, which is why hair and rings are spoken as good practice, not rule); WAC 296-806-20020 (power-driven machinery completely stopped before making adjustments or repairs, or removing material or refuse; exemption if the machine has to be in motion to properly adjust it; its reference points to lockout, chapter 296-803 WAC). Behind "the company's part": WAC 296-806-20028 to -20040 (the employer protects employees from the point of operation, nip or shear points, rotating, reciprocating and other moving parts, flying and falling objects, and moving surfaces with hazards, by one or more safeguarding methods); the method may be a guard, a device, distance or location, so "the right guard" is plain talk for "the right safeguard." Behind "that's a lockout job": WAC 296-803-100 (lockout chapter applies to service and maintenance where employees could be injured by unexpected start-up or release of stored energy; it has exemptions, among them cord-and-plug equipment that is unplugged and under the worker's control, and minor routine service during normal production done with effective protection, which is why the talk says "ask your supervisor how lockout works on that machine" and does not say "the rule says"). Federal: 29 CFR 1910.212(a)(1), (2), (3) (one or more methods of machine guarding; guards affixed to the machine where possible and not a hazard in themselves; point of operation guarded). The federal section has no line on the worker's own duties; those come from Washington's core rules.