R Safety Hub R Safety Hub Your prescription for a safer workplace

Positioning Devices for Rebar and Form Work

Lines in italics are for the reader, not the crew. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is for anybody tying rebar on a wall or column, or working on the face of a form. You know the move. You're up on the mat, both hands busy with the tie wire, leaning back.

Leaning back on what? That's today.

When the rule kicks in

Washington's rule says if you're placing or tying rebar, or working on the face of formwork or rebar, and you could fall four feet or more, you're protected. One of three ways: a personal fall arrest system, a positioning device system, or a safety net.

Four feet. Not six. Six is the federal number. In Washington it's four.

What a positioning device is

A positioning device holds you against the wall or column so you can work with both hands free. You wear a full body harness or a positioning harness, and the device clips you to the rebar or the form.

It is not the same as fall arrest. It holds you in place. The rule says it has to be rigged so you can't free fall more than two feet.

What it hooks to

The anchorage has to hold at least twice the impact of your fall, or three thousand pounds, whichever is more. In plain words, it hooks to something solid. Not a single loose bar, and not a tie that's half done. If you're not sure the mat will hold, ask before you lean on it.

The snap hooks have to be the locking kind. And unless the hook is designed for it, it doesn't clip straight onto webbing or rope, onto another snap hook, onto a D-ring that already has another hook on it, onto a horizontal lifeline, or onto anything shaped so it could pop the keeper open.

Check it every time

The harness, the hooks and the device get looked over before each use, the way the maker says. Cuts, burns, mildew, frayed webbing, bent or rusty hardware, a keeper that doesn't snap shut. If it's damaged, it's out. And this gear protects people. It is never used to hoist material. No pulling the bundle up with your positioning strap.

Somebody always says, "I've got good balance." Great. Balance doesn't hold you when a bar rolls under your boot.

Moving around

The hard part is climbing up and moving between spots. Ask how you stay protected while you move. On a job with falls of ten feet or more, the company's written fall protection work plan has to cover how the system is set up and used.

Before you use this gear, a competent person trains you, you show you can use it right, and the company keeps a written record. If you haven't been shown, say so. And the company has to plan for getting you down fast if you do fall.

Talk it over

  1. What are we hooking our positioning devices to on this job, and is it solid?
  2. What would make it easier to stay protected while we climb the mat from one spot to the next?

Before you go

Four feet or more on rebar or forms means protection, no more than two feet of free fall, locking hooks on something solid, and check it before every use.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-880-20005(5) (employees exposed to fall hazards of four feet or more while placing or tying reinforcing steel or working on the face of formwork or reinforcing steel protected by personal fall arrest, positioning device or safety net systems); 296-880-095(42) (positioning device system: full body harness or positioning harness rigged to support an employee on an elevated vertical or inclined surface such as a wall, pole or column, working with both hands free); 296-880-40030(1) to (9) (positioning or full body harness; free fall not greater than two feet; anchorage at least twice the potential impact load or 3,000 pounds, whichever is greater; connector materials and finish; 5,000-pound connecting assemblies; 3,600-pound proof-tested D-rings and snap hooks; locking snap hooks; snap hooks not engaged, unless designed for it, directly to webbing, rope or wire rope, to each other, to a D-ring with another connector attached, to a horizontal lifeline, or to an incompatibly shaped object); 296-880-10005(2)(a), (3) (components inspected before each use according to the manufacturer; used for employee protection, not to hoist materials); 296-880-10015 (training by a competent person); 296-880-10020 (written work plan at ten feet). Federal: 29 CFR 1926.501(b)(5) (face of formwork or reinforcing steel, six feet or more: personal fall arrest, safety net or positioning device systems); 1926.502(e)(1) to (10) (two-foot free fall; anchorage; connectors; snaphooks; inspection before each use; not to hoist materials); WAC 296-880-10005(4) (prompt rescue or self-rescue). "Leaning back on what," "something solid; not a single loose bar, not a half-done tie," "ask before you lean on it," the damage examples, "no pulling the bundle up with your strap," the balance line, and the 'ask how you stay protected while you move' line are plain explanation or good practice, not rule text.