R Safety Hub R Safety Hub Your prescription for a safer workplace

Pump Jack Scaffolds

Lines in italics are for the reader, not the crew. This one is for crews that use pump jacks. If a set is up on site, give the talk beside it. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is pump jacks. If you hang siding, you may know them better than I do. Two poles, two jacks, a platform, and you pump your way up the wall.

It is simple gear. And because it is simple, it gets set up in a hurry. A pump jack will take you up as fast as you can pump. It has no opinion on whether the pole is braced. That part is on us.

The jacks

Washington's scaffold rule says pump jack brackets, braces and accessories are made from metal plates and angles.

Each bracket has two positive gripping mechanisms, to prevent any slipping or failure. Two. If one of them is worn or missing on your jack, that jack is not ready to use.

The poles

Poles get secured to the building with rigid triangular bracing, or something equal to it. At the top. At the bottom. And at other points on the pole as necessary.

Now the part that gets skipped. Sooner or later the jack has to pass a brace on its way up. The rule says you do not just pull that brace and pump past. First you put in an extra brace, about four feet above the one you need to pass. You leave it in. You move the jack past. You put the original brace back. Then the extra one can come out.

Now the one people miss: the mid brace. On a tall pole, braces at the top and bottom are not enough. Three sets of maker's instructions for aluminum pump jack systems that we read say that once the pole goes past twenty-four feet, you need braces in between, no more than sixteen feet apart. Other makers want them closer, every twelve feet, or every ten.

That is the maker's instruction. It is not Washington's rule. The rule only says top, bottom and other points as necessary. So read the maker's instructions for the set you own, and follow them. All three of those sets of instructions say wooden poles may not be used with their systems. If your poles are wood, the rule's bracing still applies in full.

A mid brace is also a brace the jack has to pass. So that is where the extra brace goes in. Some sheets describe passing a brace another way. Washington's rule asks for the extra brace, so it stays, whatever the sheet says.

If you use wood poles, the rule says straight-grained wood, free of shakes, big loose or dead knots, and other defects that could weaken it. If a pole is made of two long pieces, the seam runs parallel to the bracket. And where two-by-fours are spliced to make a pole, every splice gets a mending plate.

The platform and the bench

The platform on a pump jack has to be at least twelve inches wide.

And the work bench is not a platform. The rule says it plainly. Work benches are not used as scaffold platforms. The bench is for material. It is not for boots.

Falls

Washington's rule for scaffolds says that at ten feet or more, each person on the scaffold is protected by guardrails or by a personal fall arrest system.

There is also a gap rule. If the front edge of the platform is more than fourteen inches from the wall you are working on, you need a guardrail along that front edge, or fall arrest.

Before anybody goes up

Scaffolds are put up, moved, changed and taken down under a competent person, by trained and experienced people the competent person picks.

A competent person looks the scaffold over before each shift, and again after anything happens that could have affected it. A truck bumping a pole counts.

And it gets loaded the way the maker's instructions say, or to a qualified person's design, and never past its rated or intended load, whichever is less. The maker's instructions also tell you how high your system can go. Read them for the set you actually have, because different systems have different answers.

Talk it over

  1. Who on this crew checks the pole bracing, and the mid brace on a tall pole, before the first person goes up?
  2. When we pass a brace, what do we actually do? Does it match what the rule says?

Before you go

Braced top and bottom, and in between when your maker's sheet says the pole is tall enough. Read it for the spacing. An extra brace in before you pass one. And nobody stands on the bench.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-874-40032(1), (2) (metal plates and angles; two positive gripping mechanisms), (3) (rigid triangular bracing or equivalent at top, bottom and other points as necessary), (4) (extra brace approximately four feet above the brace to be passed, left until the jack has moved and the original brace is reinstalled), (5) (work benches not used as platforms), (6), (7), (8) (wood poles; seam parallel to the bracket; mending plate at splices); 296-874-20010 Table 1 (pump jack platform minimum 12 inches); 296-880-30030(1) (scaffolds: guardrails or personal fall arrest at ten feet or more), (5)(b) (front edge more than fourteen inches from the work face); 296-874-20004 (erected, moved, dismantled under a competent person by trained and experienced employees); 296-874-20034 (inspection before each shift and after anything that could affect it); 296-874-20038 (loaded per the maker's instructions or a qualified person's design). Federal: 29 CFR 1926.452(j)(1), (2), (4). Other makers read use different spacing (12 feet; 10 feet), so the talk says to read the sheet for the set in hand. The WAC gives no height or spacing; the rule's extra brace four feet above is kept because it is the stricter of the two (Alum-A-Pole's sheet describes only a worker lying prone to release and reattach the brace; other sheets match the WAC). Pump jack height limits stay with the maker's sheet. "That jack is not ready to use," "a truck bumping a pole counts" and "to prevent any slipping or failure. Two." are plain explanation, not rule text. The names stay in this reference note only, as where the facts came from. The three agreeing sheets are one family of aluminum systems, so the talk says "three makers we read," not "most."