R Safety Hub R Safety Hub Your prescription for a safer workplace

Raised Beds, Blades and Parked Equipment

Lines in italics are for the reader, not the crew. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is about the heavy stuff that's up in the air when it shouldn't be. A dump bed that's raised. A loader bucket held up. A dozer blade off the ground.

Hydraulics hold things up. Hydraulics also leak, get bumped, and let go. Gravity doesn't take a break.

Nobody under a held-up load

If a machine, or part of one, is held up by slings, a hoist or jacks, it gets solidly blocked or cribbed so it can't fall or shift before anybody works under it or between it. That's the rule. Not "I'll only be a second." Blocked first, then you go under.

Blades, buckets and dump beds get lowered all the way, or blocked, any time they're being repaired and any time they're not in use. Controls go to neutral, the motor gets shut off, and the brakes get set, unless the job being done needs it otherwise.

Dump trucks

A truck with a dump body is required to have a built-in support, like a prop or a brace, that locks the bed up so it can't come down by accident during maintenance or inspection. A raised bed being worked on has to be blocked. The way we read it, that built-in support is what gets locked in place, and the hydraulics are not the support.

The dump control has a latch or similar device so it can't get bumped on by accident. And the tailgate trip handle is set up so the driver is in the clear when dumping. Good practice: if the support, the latch or the handle is broken, report it and keep the truck out of service until it's fixed.

Trucks get a check at the start of every shift too, brakes and parking brake included. Defects get fixed before the truck goes back to work.

Parking

Any time heavy equipment is parked, the parking brake gets set. On a slope, the wheels get chocked too.

Before a driver walks away from a truck, the motor is off and the parking brake is on. On a slope, the wheels get turned into the curb or berm, and if there's no curb or berm, they get chocked or otherwise held. Our advice: on a slope, chock it anyway. Chocks are cheap.

Equipment left unattended at night next to a road in use, or next to where work is going on, gets lights or reflectors, or barricades with them, so people can see it.

Good practice

Not rule text, just good sense. Never walk under a raised bucket or bed to save a few steps. Walk around. If you see somebody under something that isn't blocked, say something right then. "Hey, is that blocked?" takes two seconds. If a support or a chock is missing, get one before the work starts, not after.

Talk it over

  1. Where are the blocks and chocks kept on this job? Could you find one in a minute?
  2. Has anybody ever ducked under a raised bed or bucket because it was quicker?

Before you go

Lowered or blocked, locked support under a dump bed, brake set, chocked on a slope. And our own rule of thumb: nobody goes under anything that isn't blocked.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-155-605(1)(a) (unattended equipment at night next to a highway or active work: lights, reflectors, or lighted barricades), (1)(c)(i) (machinery held aloft by slings, hoists or jacks blocked or cribbed before employees work under or between; blades, buckets, dump bodies fully lowered or blocked when repaired or not in use; controls neutral, motors stopped, brakes set unless the work requires otherwise), (1)(c)(ii) (parked: parking brake set; on inclines, wheels chocked and brake set); WAC 296-155-610(2)(b) (before leaving a motor vehicle unattended: motor stopped; parking brake on and wheels turned into curb or berm on an incline; chocked or otherwise secured with no curb or berm), (2)(j) (dump bodies: permanently attached positive means of support, lockable, for maintenance or inspection; operating levers with a latch or detent; tailgate trip handles arranged so the operator is in the clear), (2)(l) (defects corrected before service). Federal: 29 CFR 1926.600(a)(1), (a)(3)(i), (ii); 1926.601(b)(10), (11), (12). The motor-vehicle unattended line (610(2)(b)) is Washington wording; the federal parallel for vehicles was not looked for. "Hydraulics leak, get bumped and let go" and "the hydraulics are not the support" are plain explanation; the good-practice section is labelled aloud. "A raised bed being worked on has to be blocked, so the support is what gets locked" combines 605(1)(c)(i) (dump bodies lowered or blocked when repaired) with 610(2)(j) (the support exists for maintenance or inspection); our reading. "A curb doesn't replace the chocks" applies 605(1)(c)(ii) to equipment; "when in doubt, chock it" and "nobody under anything not blocked" are good practice and our safe reading, stricter than the text. Keeping a truck with a broken support, latch or handle out of service is labelled good practice (those items are not named in the 610(2)(l) checklist).