R Safety Hub R Safety Hub Your prescription for a safer workplace

Ramps, Runways and Walkways

Lines in italics are for the reader, not the crew. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is about the temporary ramps and walkways we build to get from here to there. The plank over the trench. The ramp up to the scaffold. The runway across the joists.

They go up in five minutes, and then they stay up for five weeks. Every one of us walks them a hundred times without looking down.

Wide enough

A ramp, runway or inclined walkway is at least eighteen inches wide. A single two-by-ten plank isn't eighteen inches. One board is a balance beam, not a walkway.

Not too steep, and cleated

A ramp or runway is not inclined more than twenty degrees from level. That's about one foot up for every three feet across. Steeper than that, plain sense says use stairs or a ladder, not a ramp.

When it's inclined, it gets cleats or some other treatment so feet don't slip. For ramps and walkways up to a scaffold, the rule spells it out: steeper than one foot up in eight feet across, it has cleats, fastened securely to the planks, no more than fourteen inches apart.

A wet plywood ramp with no cleats in November is a slide.

Guardrails at four feet

If the ramp, runway or walkway is four feet or more above the ground or the level below, it gets a standard guardrail along each open side. If tools, parts or material are likely to be used on it, there's a toeboard on each open side too, to protect people working or walking underneath.

There's one narrow exception. A runway used only for a special purpose can leave the guardrail off one side when the work truly needs that side open, as long as the runway is at least eighteen inches wide.

Build it to carry the load

A ramp built for people walking is not automatically good for a loaded wheelbarrow or a concrete buggy. Concrete buggy runways have their own rule. They are built to carry the heaviest expected load with a safety factor of four, with a smooth running surface and standard railings, and a four-by-four inch wheel guard along the outside edge where motor-driven buggies run. And they're wide enough for two buggies to pass, or a single run at least forty-two inches wide with turnouts. Small jobs with one buggy, or one-way traffic, can skip the passing room. And a runway under twelve inches high, used only by hand-powered buggies, may skip the guardrails and wheel guards.

Use it right

Here's the crew part. Most of this is plain sense, not rule text. Keep the ramp clear of cords, hoses, cutoffs and tools. Secure the ends so the plank can't kick out or slide, and fix a plank that moves before the next person crosses. Don't overload it. If the guardrail is missing, the cleats are gone or the plank is cracked, tell your supervisor and keep people off it until it's fixed.

Somebody always says, "It's only temporary." So is the fall. The injury might not be.

Talk it over

  1. Which ramp or walkway on this job do you trust least, and why?
  2. Who built our ramps, and who checks them after rain?

Before you go

Eighteen inches wide. Not steeper than twenty degrees, and cleated. Guardrail at four feet up, and standard railings on buggy runways. Clear, secure, not overloaded.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-880-40010 (ramps, runways and inclined walkways at least 18 inches wide; not inclined more than 20 degrees from horizontal; when inclined, cleated or otherwise treated to prevent slipping); 296-880-20005(2)(a), (b) (four feet or more above the ground or lower level: standard guardrail on each open side; toeboard on each open side where tools, machine parts or materials are likely to be used; special-purpose runways may omit the guardrail on one side where operating conditions require, if at least 18 inches wide); 296-874-20030 (amended eff. 8/21/26: scaffold access ramps and walkways not steeper than 1:3, 20 degrees; steeper than 1:8, cleats securely fastened, not more than 14 inches apart); 296-155-682(7) (concrete buggy runways: maximum contemplated load with a safety factor of 4, smooth running surface, width for two buggies to pass or single runs at least 42 inches with turnouts, standard railings; exceptions for one-buggy jobs and one-way traffic; Exemption: runways less than 12 inches above the floor or ground used by buggies the rule's text calls 'hard-powered' (read here as an apparent typo for hand-powered, our reading) may be exempt from the guardrail and wheelguard requirements). Federal: 29 CFR 1926.451(e)(5) (scaffold access ramps and walkways: guardrails at six feet, not steeper than 1:3, cleats not more than 14 inches apart when steeper than 1:8). Differences seen: Washington guardrails at four feet, federal six (scaffold access ramps). No general federal ramp section was searched beyond 1926.451. "One foot up for every three across" is the 1:3 slope named in 296-874-20030 and is used as a plain description of 20 degrees. "A two-by-ten isn't eighteen inches," keep it clear, secure the ends, don't overload, tell your supervisor are plain sense or good practice, and the talk says so.