R Safety Hub R Safety Hub Your prescription for a safer workplace

Rebar and Impalement Hazards

Lines in italics are for the reader, not the crew. If you can, point at a piece of standing rebar on this job while you talk. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is about something that sticks up out of the ground and waits. Rebar. And anything else sharp and pointed that a person could land on.

Most of the time we think about falls in terms of height. Four feet, ten feet, the roof. Today is different. With impalement, height is not the question. What you land on is the question.

What the rule says

Washington's rule is plain. No matter how high you are, the company has to protect you from falling into or onto something that can impale you. The rule names rebar, exposed steel and wood as examples. So a person who trips on flat ground next to a row of rebar is covered, same as somebody working above it.

And the concrete rule says all sticking-up rebar a worker could fall onto or into has to be guarded, so the impalement hazard is gone. Not reduced. Gone.

Federal OSHA's rule says the same thing, almost word for word.

What guarding looks like

The rule does not name one product. Caps, covers, troughs. There is more than one way. Not every cap is built for the same job, so use what the company gives you, and read the label. If you look at a cap and you are not sure it would hold you, ask. That's a fair question.

Good practice: walk your area at the start of the shift. Count the open bar ends. Any one without a cap or cover gets one, or gets reported, before work starts near it. That is not written in the rule. It's how you make sure the rule actually happened. Also good practice: when you're carrying something that blocks your view, or stepping backward, look first for bar near you. Trips happen on flat ground, and flat ground next to rebar is not flat ground anymore.

Covers that other trades leave behind

Here is one people miss. The rebar crew puts covers on. Then the rebar crew leaves. Who owns the covers now?

The rule says the covers stay only if the general contractor told them to stay and took charge of them, or handed them to another contractor. And no matter who's in charge of the covers, your own employer still has to protect you. So if you find bar uncovered, it is not somebody else's problem. Say something.

Somebody always says, "That cap's been missing all week, and nobody's fallen yet." True. And my truck went all week without an oil change, too. That's not a maintenance plan. A week without a fall is not a safety record. It is a week of luck.

Two more things about rebar

Rebar is not a brace. The rule says reinforcing steel must not be used as a guy line or a brace. So no tying off a wall form to a stick of bar because it was handy.

And rolls of wire mesh get tied off at each end. A mesh roll that lets go springs back hard. Nobody wants to be in the way of that.

Talk it over

  1. Where on this job is there bar sticking up right now, and is every end covered?
  2. And if you found a missing cap at break time, who would you tell, and how fast would it get fixed?

Before you go

Height doesn't matter. What you land on does. Every bar end gets guarded, every time, by whoever finds it open.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-880-10010(3) (impalement hazards regardless of height; rebar, exposed steel or wood); WAC 296-155-680(10)(a) (guard all protruding reinforcing steel to eliminate impalement), (10)(b) (wire mesh rolls secured at each end), (10)(c) and note (covers left in place; each employer still protects its own workers), (9)(c) (reinforcing steel not used as a guy or brace). Federal: 29 CFR 1926.701(b). The rule names no cap or cover type; "not every cap is built for the same job," the start-of-shift walk and "ask if you're not sure" are plain explanation and good practice, not rule text. WAC 296-155-680(1) points to ANSI A10.9; this talk does not quote it.