R Safety Hub R Safety Hub Your prescription for a safer workplace

Rolling Ladder Stands

Lines in italics are for the reader, not the crew. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is about the rolling ladder. The one on wheels with steps going up to a top step or a little platform. You see them on interior jobs, in warehouses, in the supply house.

The rule calls it a mobile ladder stand. It's built for one person at a time. And it's only a friend while its wheels are locked.

Don't ride it

Nobody moves a rolling ladder stand while someone is on it. Not a little push, not "scoot me over." Get down, move it, lock it, climb back up.

If it has wheels or casters, it has to have a way to stop it rolling while someone is on it. Use it. Lock the wheels or set the brake before you climb.

Stand inside the frame

On a ladder stand, your standing area is inside the base frame. Don't lean out past the base to reach, and don't stand on a part that hangs out past the wheels.

There's a height limit too. The working height can't be more than four times the narrowest side of the base, unless it has outriggers, counterweights or something like that to keep it from tipping over. A tall, skinny stand without them is a tip-over waiting to happen.

Rails

If the top step is four feet up or more, the stand has handrails, about two and a half to three feet high, measured from the front edge of a step. If the top step is over ten feet, the top step is railed on three sides, at least three feet high. If that top step is twenty inches or deeper, it also gets a midrail and a toeboard.

On the stand models with a platform, from four to ten feet up the platform has handrails at least three feet high and midrails. Above ten feet, guardrails and toeboards on the open sides and ends.

Only in special uses can a chain or a removable gate take the place of a rail. It's not an everyday swap. Good practice: if there is one, hook it.

Built right

The steps are at least sixteen inches wide, evenly spaced, no more than ten inches apart, at least seven inches deep, and slip resistant. The stand and its wheels are built to hold at least four times the load they're meant for. That's the maker's job, but it's our job to not overload it. One person on a ladder stand.

If a wheel won't lock, a step is bent, or the slip-resistant surface is worn smooth, don't use it. Tell your supervisor.

Good practice

Not rule text. Roll it only on a clean, level floor. Push it, don't pull it toward you. And watch overhead for lights, pipes and sprinkler heads when you move a tall one.

Talk it over

  1. Do the wheel locks work on the rolling ladders we use?
  2. Has anyone ever been pushed while standing on one?

Before you go

Lock it, climb it, stay inside the frame, never ride it, and use the rails.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-876-099 (mobile ladder stand: mobile, fixed-height, self-supporting ladder, usually wheels or casters on a rigid base and steps leading to a top step, may have handrails, designed for use by one employee at a time; mobile ladder stand platform: one or more standing platforms); 296-876-100 (scope); 296-876-91005(1) to (8) (step width 16 inches; slip resistant; four times maximum intended load; wheels and casters their share of four times the load plus the unit's weight; handrails 29 1/2 to 37 inches where top step is four feet or more; work-surface height not over four times the shortest base dimension without outriggers, counterweights or comparable means; system to impede horizontal movement when an employee is on it; not moved while an employee is on it); 296-876-91010(1), (2), (3) (uniform steps, rise not over 10 inches, depth at least 7 inches; top step over ten feet railed on three sides at least 36 inches, midrail and toeboard if top step 20 inches or more front to back; standing area within the base frame); 296-876-91015(2), (3), (4) (platform 4 to 10 feet: handrails at least 36 inches and midrails; over 10 feet: guardrails and toeboards on exposed sides and ends; gates or chains only in special-use applications). Federal: 29 CFR 1910.23(e) (general industry; same items); no mobile ladder stand section was found in part 1926. "Only a friend while its wheels are locked," "scoot me over," "one person on a ladder stand" (from the definition's "designed for use by one employee at a time"), "if it's there, hook it," the damage examples and the good-practice paragraph are plain explanation or good practice, not rule text. "About two and a half to three feet" is our plain wording for 29 1/2 to 37 inches.