R Safety Hub R Safety Hub Your prescription for a safer workplace

Scissor Lifts and Boom Lifts

Lines in italics are for the reader, not the crew. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is about lifts. Scissor lifts, the ones that go straight up, and boom lifts, the ones with the arm that reaches out.

Lifts are great. They beat a ladder for a lot of jobs. But a lift is a machine that puts you up in the air on a small floor, on top of whatever ground it's parked on. When something goes wrong, it's usually one of three things. It tips. Somebody falls out. Or it touches a power line.

Trained and authorized

Only people who are trained and authorized run a lift. That means you've been through the maker's manual and the warning stickers, someone qualified has shown you every control, and you've run that model, or one with the same kind of controls, while they watched. Knowing how to run your cousin's lift on a weekend doesn't count. Every machine is a little different.

The manual lives in a weatherproof box on the machine. Know where it is.

Check it every shift

At the start of every shift, the lift gets a prestart inspection. Walk around it and use the maker's checklist. Controls, guardrails, gate, tires, hoses, leaks, anything bent or cracked. If something is wrong, it's out of service right then. Tag it and tell your supervisor.

If something feels off while you're using it, the rule is simple. Stop. Report it. Don't use it again until it's fixed.

Look at the ground and look up

Before you go up, and the whole time you're up, keep looking. Holes, drop-offs, slopes, soft ground, debris, wind, people walking under you, and overhead stuff. Beams, branches, and especially power lines.

The rule sets minimum distances from power lines. For any bare line, or any line of three hundred volts or more, it's at least ten feet. Higher voltage means more. If you're not sure what the line carries, treat it like it's the big one and stay well back.

Before you raise it, check that the machine is on ground the maker allows, outriggers out if it has them, gate shut, and the load under the rated capacity. That capacity counts you, your buddy, your tools and that box of siding.

Feet on the floor

Here's the one people break. Feet stay on the platform floor. No standing on the guardrail. No bucket, no plank, no stepladder in the basket to get a little higher. If you can't reach, move the lift. A ladder on a lift is just a taller way to fall.

On a boom lift, everybody in the basket wears a full body harness with a lanyard clipped to the anchor point the maker put there. Not the guardrail, not the building next to you.

On a scissor lift, the guardrails are your main fall protection. So the gate stays closed and the rails stay on.

Driving it

Drive slow enough for the ground, the slope, the crowd and what you can see. If you drive with it up, keep a clear view and stay well away from holes and edges. And no horseplay. A lift is not a ride.

Don't lean it against the building to steady it, and don't use it as a crane.

Talk it over

  1. Who here is trained on the lift we have today? Is it the same model you trained on?
  2. Where are the power lines and drop-offs around where we'll be working?

Before you go

Trained, checked, look up, feet on the floor. And on a boom, clip in.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-869-50005, -50010 (trained and authorized; manuals, decals, controls, demonstration on same or similar model; manuals' weather-resistant compartment); -40005, -40010(1) and Table 2 (prestart at the beginning of each shift; out of service if not in proper condition); -60045 (cease, report, discontinue); -60010 (survey before and during use); -60035(1) and Table 6 (before raising; minimum safe approach distance, ten feet for uninsulated lines and 300 volts to 50 kV, more above 50 kV); -60040 (firm footing; no guardrails, planks or ladders for height; harness and lanyard on boom-supported platforms; guardrails primary on scissor-type); -60020, -60025, -60030 (no leaning on objects, speed, driving elevated, no horseplay); -60005 (not a crane). Federal: 29 CFR 1926.453(b)(2) (vehicle-mounted aerial lifts). The walk-around items named are examples; the maker's checklist and the WAC's Table 2 govern. "Treat an unknown line as the big one" is good practice, not a rule.