R Safety Hub R Safety Hub Your prescription for a safer workplace

Seat Belts, Riding and Rollover Protection

Lines in italics are for the reader, not the crew. How to read a talk

Printable version with sign-in sheet (PDF)

Read this out loud

Morning, everybody. Today is about riding. In the crew truck, on the loader, on anything with wheels or tracks on this job.

We all buckle up on the highway. Then we get on site, the speed drops to a crawl, and the belt stays loose. "It's only across the lot." The ground on a job site is rougher than any highway.

Trucks and work vehicles

In Washington, every truck and work vehicle on a construction site has seat belts, and the rule says they get used by everybody inside. Driver and every passenger.

A vehicle carrying workers needs seats firmly secured, and enough of them for everybody riding. The way we read that: nobody rides in the truck bed, on the tailgate, or on the load. If there's no seat for you, you take the next trip.

Tools and material riding in the same space as people get tied down or secured. A loose toolbox in a sudden stop turns into a flying toolbox.

Loaders, dozers, tractors and the like

On earthmoving equipment, seat belts get used by the operator and any passenger. There are a few exceptions. A machine built only for stand-up operation doesn't need one. Mechanics and people in training may ride along without one if the machine doesn't have one for them. Otherwise, belted.

And here's a part people don't expect. The rule says you don't use a seat belt on a machine that has no rollover protection or proper canopy in place. That frame over the seat is what protects you if the machine goes over. The belt is what keeps you inside it.

That's for the machines, not the trucks. In a truck, you're always belted.

The rollover frame

That frame is called a ROPS, a rollover protective structure. Rubber-tired loaders, dozers and scrapers, crawler tractors and loaders, graders, and wheel-type farm and industrial tractors used in construction are required to have one. If one of those machines shows up without its frame, it's not ready to run. Don't use it. Report it. Skid steers and compactors: the federal rule requires a frame on ones built after July 2019, so ask your supervisor what applies to ours.

If a ROPS ever comes off, for any reason, it goes back on with bolts or welding as good as the original, or better. Not with whatever was in the bucket of the truck. And each one has a label naming its maker and the machine it fits. If the label is gone or the frame doesn't match the machine, say something.

Good practice: no drilling, cutting or welding on the frame to hang a light or a toolbox. Ask first. A frame that has been cut may not hold the way it was built to.

Before the shift

The rule says trucks and work vehicles get checked at the start of every shift. Seat belts are on that list, right next to brakes, tires and the horn. A belt that won't latch is a defect, and defects get fixed before the vehicle goes back to work.

Talk it over

  1. Honest answer: when did you last ride across this site without a belt?
  2. Is there any machine here with a missing belt, a bad latch, or a frame somebody has modified?

Before you go

A seat and a belt for everybody, nobody in the bed, frame on the machine, and buckle up even at a crawl.

Short on time, or no one to lead it? Doc and Red can run this talk for you in the R Safety Hub app.

Get started

Reference (not read aloud). Washington: WAC 296-155-610(1) (motor vehicles operating on a construction site; equipment under -615 excluded), (2)(i) (tools and material secured when carried with employees; seats firmly secured and adequate for the number carried; seat belts installed in all motor vehicles and used by all occupants), (2)(l) (start-of-shift check includes seat belts, brakes, tires, horn; defects corrected before the vehicle goes into service); WAC 296-155-615(1)(a), (b) (earthmoving equipment; seat belts provided and used by all operators and passengers; exemption for stand-up equipment; seat belts not used on equipment without ROPS or adequate canopy; mechanics and persons in training may ride without a belt if one is not provided), (1)(f) (ROPS: see -950 to -965); WAC 296-155-950(1) (scrapers, loaders, dozers, agricultural and industrial tractors, crawler tractors and loaders, motor graders used in construction; not sideboom pipelaying tractors; compactors and rubber-tired skid steers reserved), (3)(b)(i) (design aim: minimize the chance of the operator being crushed in a rollover), (4) (remounted with equal or better bolts or welding), (5) (label: maker, model, machine it fits). Federal: 29 CFR 1926.601(b)(8), (9), (14); 1926.602(a)(2); 1926.1000. Differences seen: federal 1926.601(b)(9) requires seat belts installed in all motor vehicles; the "used by all occupants" wording is Washington's. Federal 1926.602(a)(2)(iii) says belts "need not be provided" without ROPS; Washington says you "must not use" them. "Nobody in the truck bed, tailgate or load" is our plain reading of the secured-seats line for vehicles carrying workers. "The belt keeps you inside the frame" is plain explanation of why the rule ties belts to ROPS. No modifying the frame without asking is good practice (the rule covers remounting, not modification). The SAE seat belt and ROPS test standards the rules name are not detailed. "Report a covered machine with no frame" follows from -950(2), (3) (covered equipment must be equipped or fitted with ROPS). Skid steers and compactors: Washington's -950(1)(b) reserves them; federal 1926.1000(a) covers those made after July 15, 2019; the talk sends the crew to the supervisor.